-
- CNC/3D Printer, Motor Controller Module
A4988 StepStick Stepper Motor Driver Module
- ৳170.00
- This breakout board for Allegro’s A4988 microstepping bipolar stepper motor driver features adjustable current limiting, overcurrent and over-temperature protection, and five different microstep resolutions (down to 1/16-step). It operates from 8 V to 35 V and can deliver up to approximately 1A per phase without a heat sink or forced air flow (it is rated for 2 A per coil with sufficient cooling)DishanTech…
- Add to cart
-
- Motor Controller Module
AC Motor Speed Controller 220V 4000Watt
- ৳645.00
- Description: Operating voltage: AC 220 V. Control voltage: AC 10-220V. Maximum power: 4000W (resistance load), the power should be reduced for a long time. It is recommended to use the resistance load at room temperature within 2000W. Efficiency: 90%. Dimensions: 85 x 55 x 38 mm, buttonhole 6 mm.
- Add to cart
-
- Brush Less Motor, Motor Controller Module
Brushed ESC 20A with Brake
- ৳550.00
- Item type: Brush Motor Speed Controller 20A brush speed controller. Function: forward, reverse, brake Working voltage: 3.0V — 9.4V. Current(A): 20A Driver frequency: 2KHz Input: Li-Po 2S / Ni-Mh/Ni-cd 4-7 cell Constant current 20A Max 25A< 30s> Pulsed 50A< 5s> This ESC can work with 130/180/260/280/380 Brush Motor Item dimension: 10 * 2 * 0.5cm Item weight: 8g
- Add to cart
-
- DC Motors & Wheels, Motor Controller Module
BTS7960 Motor Driver Module
- ৳799.00
- Model: IBT-2 Double BTS7960 large current (43A) H-Bridge motor driver 5v isolate with MCU and effectively protect MCU Can solder heat sink Supply voltage: 5.5-27 V Input level: 3.3-5V Maximum current: 43A Control mode: PWM or level PWM I/P: 25 kHz. Duty cycle: 0-100% Current diagnostic Slope adjustment Dead Time generation Overtemperature, overvoltage, undervoltage, overcurrent protection Short circuit protection
- Add to cart
-
- Motor Controller Module
DRV8825 Purple Stepper Motor Driver
- ৳235.00
- Simple step and direction control interface Six different step resolutions: full-step, half-step, 1/4-step, 1/8-step, 1/16-step, and 1/32-step Can interface directly with 3.3 V and 5 V systems Over-temperature thermal shutdown, over-current shutdown, and under-voltage lockout Short-to-ground and shorted-load protection 4-layer, 2 oz copper PCB for improved heat dissipation Exposed solderable ground pad below the driver IC on the bottom of…
- Add to cart
-
- CNC/3D Printer, Motor Controller Module
DRV8825 Stepper Motor Driver Module
- ৳220.00
- Supply Voltage: 8.2 – 42 VDC. Current Capacity : 2.2A max(24V). Continuous current per phase: 1.5 A. Minimum Logic voltage: 2.5V. Maximum Logic Voltage: 5V. Microstep resolutions: full, 1/2, 1/4, 1/8, 1/16, and 1/32. Dimensions : 15 x 20 mm. Weight: 4 gm.
- Add to cart
-
- Arduino Shield & Module, Motor Controller Module
L-298P Motor Driver Expansion Board
- ৳520.00
- Features: L298P dual-end full-bridge drive chip can be used to independently drive two dc, stepper motor or relay at the same time. The current value of the motor can be measured in real time. Fully compatible with Arduino UNO R3, laminated plug-in design, direct reading of current through analog IO. compatible with TinkerKit, can be directly inserted with it.
- Add to cart
-
- Basic Components, Digital ICs, Motor Controller Module
L293D Dual H-bridge
- ৳119.00
- Maximum Supply Voltage: 36 V Maximum Logic Supply Voltage: 36 V Maximum Input Voltage: 7 V Maximum Enable Voltage: 7 V Peak Output Current (100 ms non-repetitive): 1.2 A Total Power Dissipation at 90°C: 4 W Storage and Junction Temperature: – 40 °C to 150 °C
- Add to cart
-
- Motor Controller Module
L293D Dual Motor Driver Module
- ৳245.00
- Model: L293D Brand: China
- Add to cart
-
- Arduino Shield & Module, Motor Controller Module
L293D Motor Driver Module
- ৳320.00
- New L293D motor shield, the input voltage DC4.5-25V 600mA output current capability per channel 1.2A peak output current(non-repetitive) per channel Enable facility Overtemperature protection Logical “0” input voltage up to 1.5V(High noise immunity)
- Add to cart
-
- DC Motors & Wheels, Motor Controller Module
L293D Motor Driver Shield
- ৳349.00
- DC Motor/Stepper Motor + Servo Shield 2 interface for 5V Servo connected to the Arduino's high-resolution dedicated timer - no jitter. Can drive 4 DC motors or 2 stepper motors or 2 Servo. Up to 4 bi-directional DC motors with individual 8-bit speed selection. Up to 2 stepper motors (unipolar or bipolar) with single coil, double coil or interleaved stepping.…
- Add to cart
-
- Motor Controller Module
L298N DC Motor Driver Module_Green
- ৳335.00
- Driver chip: L298N dual H-bridge DC motor driver chip Driving portion of the terminal supply area Vs: + 5V ~ + 35V; if necessary to take power within the board, the power supply range Vs: + 7V ~ + 35V Part of the peak current drive Io: 2A Logical part of the terminal supply area Vss: + 5V ~ +…
- Add to cart
