-
- Arduino Shield & Module
8 Channel 12V Relay Module
- ৳1,290.00
- Operating Voltage: 12V DC Equipped with high-current relay 10A 250VAC / 10A 30VDC It can control both AC and DC appliances such as Solenoids, Motors, lights, fans, etc. High-quality screw terminals (Terminal Block) provided (C, NC, NO) for quick and easy connection. Freewheeling diode to protect your microcontroller. Input Signal Pin connected to Burg stick for easy accessibility. LED Status…
- Add to cart
-
- Arduino Shield & Module
8 Channel 5V Relay Module
- ৳1,150.00
- Channel: 8 channel Relay Operating Voltage: 5V One normally closed contact and one normally open contact Triode drive, increasing relay coil High impedance controller pin Pull-down circuit for the avoidance of malfunction Power supply indicator and Control indicator lamp Power supply and relay instructions, lit, the disconnect is off
- Add to cart
-
- Arduino Shield & Module
8 Channel 5V Relay Module
- ৳620.00
- Features: 1. This is a 5V 8 channel relay module with optocoupler isolation. 2. 1 relay output module, max load AC 250A 10A, DC 30V 10A. 3. VCC, GND power input, can separately supply relay power input JD-VCC. 4. Input IN1, IN2, IN3, IN4, IN5, IN6, IN7, IN8 signal line low level trigger. 5. Widely used in SCM control, PLC control, home intelligent control, industry etc.
- Add to cart
-
- Arduino Shield & Module
9V Relay
- ৳30.00
- 9V Relay
- Add to cart
-
- Arduino Shield & Module
A6 Pro Serial GPRS GSM Module
- ৳1,050.00
- Working frequency: quad-band network, 850 / 900 / 1800 / 1900MHz Working voltage: 4.8-9VDC(On-board voltage regulator circuit supply power for A6 module) Working Current: maximum of 2A.
- Add to cart
-
- Arduino Shield & Module, BMS & Charger, Sensors
AC 0~5A Analog Current Meter Module Ammeter Sensor Board
- ৳520.00
- Onboard precision microcurrent transformer. Onboard sampling resistor. The module can measure AC currents less than 5A, the corresponding analog output 5A/5mA. Rated input current: 5A Rated output current: 5mA Change: 1000: 1 The linear range: 0 ~ 10A (100 ohms) Linearity: 0.2%
- Add to cart
-
- Arduino Shield & Module, Current, Sensors, Touch
AC Light Dimmer Module, 2 Channel, 3.3V / 5V logic, AC 50 / 60hz, 220V / 110V
- ৳1,055.00
- High-quality BTA16-600B TRIAC AC Voltage: 220V/110V; 50/60Hz Rated current: 5A Logic: 3.3V/5V Peak Operating Current: 8A Dishan Tech BD.
- Add to cart
-
- Sale!
- Arduino Shield & Module, Sensors
AD8232 ECG Measurement Module Kit
- Original price was: ৳2,750.00.৳2,550.00Current price is: ৳2,550.00.
- Designed to extract, amplify, and filter small biopotential signals. Leads-Off Detection. Shutdown Pin. LED Indicator. Analog Output. 3.5 mm Jack for Biomedical Pad Connection. DishanTech BD.
- Add to cart
-
- Arduino Shield & Module
Ai-Thinker RA-02
- ৳695.00
- Specifications 433MHz Average Operating Current TX: 93mA RX: 12.15mA Standby: 1.6mA Best suited for long range Internet of Things application Can be used with Arduino, Raspberry Pi, ARM, PIC etc. - Supports half-duplex SPI communication Color: Multicolor LoRa Spread Spectrum modulation technology Constant RF power output at + 20dBm-100mW voltage change High sensitivity: down to -148dBm Half-duplex SPI communication Programmable…
- Add to cart
-
- Arduino, Arduino Board
Arduino Compatible ESPLORA Game Programming Module Board
- ৳1,720.00
- The Arduino Esplora has onboard sound and light outputs, and several input sensors, including: Joystick Slider Temperature sensor Accelerometer Microphone Light sensor RGB LED
- Add to cart
-
- Arduino, Arduino Board, Development Board
Arduino Due
- ৳3,450.00
- Microcontroller: AT91SAM3X8E Operating Voltage: 3.3V Input Voltage (recommended): 7-12V Input Voltage (limits): 6-16V Digital I/O Pins: 54 (of which 12 provide PWM output) Analog Input Pins: 12 Analog Outputs Pins: 2 (DAC) A 32-bit core, that allows operations on 4 bytes wide data within a single CPU clock. CPU clock at 84Mhz 96KBytes of SRAM
- Add to cart
-
- Arduino Board, Development Board
Arduino Ethernet Shield W5100
- ৳1,200.00
- Operating voltage: 5V (supplied from the Arduino Board) Ethernet Controller: W5100 with internal 16K buffer Connection speed: 10/100Mb Connection with Arduino on SPI port The Shield contains a number of informational LEDs PWR: indicates that the board and shield are powered LINK: indicates the presence of a network link and flashes when the shield transmits or receives data.DishanTech BD. FULLD:…
- Add to cart
