-
- Arduino Shield & Module
KY023 KY-023 JOYSTICK Dual Axis XY Joysticks 5 Pin 5V Module
- ৳119.00
- the module has two-way analog output and a digital output interface, the output value corresponding to (X, Y) bi-axial offset, the type of analog; keys that the user press, the Z axis is a push switch read as digital input.
- Add to cart
-
- Arduino Shield & Module, Motor Controller Module
L-298P Motor Driver Expansion Board
- ৳520.00
- Features: L298P dual-end full-bridge drive chip can be used to independently drive two dc, stepper motor or relay at the same time. The current value of the motor can be measured in real time. Fully compatible with Arduino UNO R3, laminated plug-in design, direct reading of current through analog IO. compatible with TinkerKit, can be directly inserted with it.
- Add to cart
-
- Arduino Shield & Module, Motor Controller Module
L293D Motor Driver Module
- ৳320.00
- New L293D motor shield, the input voltage DC4.5-25V 600mA output current capability per channel 1.2A peak output current(non-repetitive) per channel Enable facility Overtemperature protection Logical “0” input voltage up to 1.5V(High noise immunity)
- Add to cart
-
- Arduino Shield & Module, Battery & Holder, BMS & Charger, Robots
Li-Po Battery Voltage Tester
- ৳345.00
- Can be used for 1-8s Lipo/Li-ion/LiMn/Li-Fe Voltage detection precision: 0.01V Cell voltage display range: 0.5V-4.5V Total voltage display range: 0.5V-36V 1S test mode voltage range: 3.7V-30V Low voltage alarm mode for 2-8S Alarm set value range: OFF-2.7V-3.8V When the voltage is below the set value, loud buzzer sounds, pre-set value 3.3V One button setup of alarm voltage Weight: 9g
- Add to cart
-
- Arduino, Arduino Board
LILYPAD Arduino Lilypad 328
- ৳550.00
- The latest version of the LilyPad supports automatic reset for even easier programming.
- Add to cart
-
- Arduino Shield & Module, BMS & Charger, Solar Panel & Charge Controller
Lithium Battery Charging Module TP5100 2A
- ৳210.00
- Features: * Double 8.4v / 4.2v lithium rechargeable single * Programmable charge current 0.1A-2A * Programmable steady precharge current 10% -100%. * Wide operating voltage, maximum reach 18V * Red and green LED charge status indicator * Chip temperature protection, overcurrent protection, undervoltage protection * Battery temperature protection, reverse battery shutdown, short circuit protection * Switching frequency 400Khz, usable inductance…
- Add to cart
-
- Arduino Shield & Module, Basic Components
MAX7219 4 Channel Dot Matrix Display Panel
- ৳640.00
- Driver Chip: MAX7219 Input Voltage: 3.7 to 5.3 V Input Current: 320 mA Display Dimensions: 32x32x6 (LxWxH) mm PCB Dimensions: 128×32 (LxW) mm
- Add to cart
-
- Arduino Shield & Module, Digital ICs
MAX7219 Red Dot Matrix Module MCU Control Display Module
- ৳220.00
- Pin Connection Dot LED Module to the Arduino Vcc – 5V GND – GND DIN – Pin 12 CS – Pin 10 CLK – Pin 11 Features : Requires only 3 communication wires of MCU Cascading multiple Matrix LED Module is very easy Size of the display is very compact The…
- Add to cart
-
- Arduino Shield & Module
MAX9814 Electret Microphone Amplifier Module
- ৳435.00
- Features: Supply Voltage: 2.7v-5.5v @ 3mA current Output: 2Vpp on 1.25V bias Frequency Response: 20Hz 20KHz Programmable Attack and Release Ratio Automatic gain, selectable max from 40dB, 50dB or 60dB Low Input-Referred Noise Density of 30nV/ Low THD: 0.04% (typ) Low Power Shutdown Mode Built-in 2V low-noise microphone bias -40°C ~ +85°C extended temperature range
- Add to cart
-
- Arduino Shield & Module, Motor Controller Module
Motor Driver – Dual TB6612FNG
- ৳410.00
- CW/CCW/short break/stop motor control modes Built-in thermal shutdown circuit and a low voltage detecting circuit Standby control to save power CW/CCW/short brake/stop motor control modes Operating Voltage(VDC): 15 Peak Current (A): 3.2 Continuous Current (A): 1.2 No. of Channels: 1
- Add to cart
-
- Arduino Shield & Module
Motor Shield L293D
- ৳200.00
- 2 connections for 5V ‘hobby’ servos connected to the Arduino’s high-resolution dedicated timer 4 H-Bridges: L293D chipset provides 0.6A per bridge (1.2A peak) with thermal shutdown protection, internal kickback protection diodes. Can run motors on 4.5VDC to 25VDC. Up to 4 bi-directional DC motors with individual 8-bit speed selection (so, about 0.5% resolution) Up to 2 stepper motors (unipolar or…
- Add to cart
