-
- Arduino Shield & Module
I2C Display Module
- ৳110.00
- Specification: I2C Address: 0X20~0X27 (the original address is 0X20,you can change it yourself) Supply voltage: 5V the backlight and contrast is adjusted by potentiometer Come with 2 IIC interface, which can be connected by Dupont Line or IIC dedicated cable Compatible for 1602 LCD 2004 LCD
- Add to cart
-
- ACTUATOR'S & ACCESSORIES, Arduino Shield & Module
I2C LCD Adapter Module
- ৳110.00
- 5V power supply. Serial I2C control of LCD display using PCF8574. RoboticsBD Backlight can be enabled or disabled via a jumper on the board. Contrast control via a potentiometer. Can have 8 modules on a single I2C bus (change address via solder jumpers)address, allowing.
- Add to cart
-
- Arduino Shield & Module, Communication Module, IR Sensor, Sensors
Infrared Remote Control Module HX1838
- ৳370.00
- Sensor uses HX1838, high sensitivity.2. Operating voltage 5V.3. Output form: Digital output.4. VCC: 3.3V-5V external voltage (can be directly connected to the 5v microcontroller and 3.3v microcontroller).5. GND: external GND.6. IN: external microcontroller I/O port, I/O port has been designed 10K pull-up resistor.7. Kit theory test distance of about 5-8 meters, but the practical application depends on the ambient factors…
- Add to cart
-
- Arduino Shield & Module, Communication Module
ISD1820 Voice Recording Module
- ৳300.00
- 1. Push?button interface, playback can be edge or level activated 2.Automatic power?down mode 3.On?chip 8? speaker driver 4. Signal 3.3V Power Supply 5.Can be controlled both manually or by MCU 6.Record up to around 10 seconds of audio
- Add to cart
-
- ACTUATOR'S & ACCESSORIES, Arduino Shield & Module
JoyStick 5Pin Breakout Module
- ৳120.00
- Dimensions: 40 x 27 x 15 (LxWxH) mm. RoboticsBD Weight: 10gm (without Hat). 2.54mm pin interface leads. Operating Voltage: 5V. Long service life and stable performance. Standard interface and electronic building blocks. Widely use in Arduino DIY projects.
- Add to cart
-
- Arduino Shield & Module
KY023 KY-023 JOYSTICK Dual Axis XY Joysticks 5 Pin 5V Module
- ৳119.00
- the module has two-way analog output and a digital output interface, the output value corresponding to (X, Y) bi-axial offset, the type of analog; keys that the user press, the Z axis is a push switch read as digital input.
- Add to cart
-
- Arduino Shield & Module, Motor Controller Module
L-298P Motor Driver Expansion Board
- ৳520.00
- Features: L298P dual-end full-bridge drive chip can be used to independently drive two dc, stepper motor or relay at the same time. The current value of the motor can be measured in real time. Fully compatible with Arduino UNO R3, laminated plug-in design, direct reading of current through analog IO. compatible with TinkerKit, can be directly inserted with it.
- Add to cart
-
- Arduino Shield & Module, Motor Controller Module
L293D Motor Driver Module
- ৳320.00
- New L293D motor shield, the input voltage DC4.5-25V 600mA output current capability per channel 1.2A peak output current(non-repetitive) per channel Enable facility Overtemperature protection Logical “0” input voltage up to 1.5V(High noise immunity)
- Add to cart
-
- Arduino Shield & Module, Battery & Holder, BMS & Charger, Robots
Li-Po Battery Voltage Tester
- ৳345.00
- Can be used for 1-8s Lipo/Li-ion/LiMn/Li-Fe Voltage detection precision: 0.01V Cell voltage display range: 0.5V-4.5V Total voltage display range: 0.5V-36V 1S test mode voltage range: 3.7V-30V Low voltage alarm mode for 2-8S Alarm set value range: OFF-2.7V-3.8V When the voltage is below the set value, loud buzzer sounds, pre-set value 3.3V One button setup of alarm voltage Weight: 9g
- Add to cart
-
- Arduino Board, Programmable Microcontroller
LILYPAD Arduino Lilypad 328
- ৳550.00
- The latest version of the LilyPad supports automatic reset for even easier programming.
- Add to cart
-
- Arduino Shield & Module, BMS & Charger, Solar Panel & Charge Controller
Lithium Battery Charging Module TP5100 2A
- ৳210.00
- Features: * Double 8.4v / 4.2v lithium rechargeable single * Programmable charge current 0.1A-2A * Programmable steady precharge current 10% -100%. * Wide operating voltage, maximum reach 18V * Red and green LED charge status indicator * Chip temperature protection, overcurrent protection, undervoltage protection * Battery temperature protection, reverse battery shutdown, short circuit protection * Switching frequency 400Khz, usable inductance…
- Add to cart
