-
- Arduino Shield & Module
8 Channel 12V Relay Module
- ৳1,290.00
- Operating Voltage: 12V DC Equipped with high-current relay 10A 250VAC / 10A 30VDC It can control both AC and DC appliances such as Solenoids, Motors, lights, fans, etc. High-quality screw terminals (Terminal Block) provided (C, NC, NO) for quick and easy connection. Freewheeling diode to protect your microcontroller. Input Signal Pin connected to Burg stick for easy accessibility. LED Status…
- Add to cart
-
- Arduino Shield & Module
8 Channel 5V Relay Module
- ৳1,150.00
- Channel: 8 channel Relay Operating Voltage: 5V One normally closed contact and one normally open contact Triode drive, increasing relay coil High impedance controller pin Pull-down circuit for the avoidance of malfunction Power supply indicator and Control indicator lamp Power supply and relay instructions, lit, the disconnect is off
- Add to cart
-
- Arduino Shield & Module
8 Channel 5V Relay Module
- ৳620.00
- Features: 1. This is a 5V 8 channel relay module with optocoupler isolation. 2. 1 relay output module, max load AC 250A 10A, DC 30V 10A. 3. VCC, GND power input, can separately supply relay power input JD-VCC. 4. Input IN1, IN2, IN3, IN4, IN5, IN6, IN7, IN8 signal line low level trigger. 5. Widely used in SCM control, PLC control, home intelligent control, industry etc.
- Add to cart
-
- Arduino Shield & Module
9V Relay
- ৳30.00
- 9V Relay
- Add to cart
-
- Arduino Shield & Module
A6 Pro Serial GPRS GSM Module
- ৳1,050.00
- Working frequency: quad-band network, 850 / 900 / 1800 / 1900MHz Working voltage: 4.8-9VDC(On-board voltage regulator circuit supply power for A6 module) Working Current: maximum of 2A.
- Add to cart
-
- Arduino Shield & Module, BMS & Charger, Sensors
AC 0~5A Analog Current Meter Module Ammeter Sensor Board
- ৳520.00
- Onboard precision microcurrent transformer. Onboard sampling resistor. The module can measure AC currents less than 5A, the corresponding analog output 5A/5mA. Rated input current: 5A Rated output current: 5mA Change: 1000: 1 The linear range: 0 ~ 10A (100 ohms) Linearity: 0.2%
- Add to cart
-
- Arduino Shield & Module, Current, Sensors, Touch
AC Light Dimmer Module, 2 Channel, 3.3V / 5V logic, AC 50 / 60hz, 220V / 110V
- ৳1,055.00
- High-quality BTA16-600B TRIAC AC Voltage: 220V/110V; 50/60Hz Rated current: 5A Logic: 3.3V/5V Peak Operating Current: 8A Dishan Tech BD.
- Add to cart
-
- Sale!
- Arduino Shield & Module, Sensors
AD8232 ECG Measurement Module Kit
- Original price was: ৳2,750.00.৳2,550.00Current price is: ৳2,550.00.
- Designed to extract, amplify, and filter small biopotential signals. Leads-Off Detection. Shutdown Pin. LED Indicator. Analog Output. 3.5 mm Jack for Biomedical Pad Connection. DishanTech BD.
- Add to cart
-
- Arduino Shield & Module
Ai-Thinker RA-02
- ৳695.00
- Specifications 433MHz Average Operating Current TX: 93mA RX: 12.15mA Standby: 1.6mA Best suited for long range Internet of Things application Can be used with Arduino, Raspberry Pi, ARM, PIC etc. - Supports half-duplex SPI communication Color: Multicolor LoRa Spread Spectrum modulation technology Constant RF power output at + 20dBm-100mW voltage change High sensitivity: down to -148dBm Half-duplex SPI communication Programmable…
- Add to cart
-
- Arduino, Arduino Board, Arduino Shield & Module, Development Board
Arduino Micro R3
- ৳1,350.00
- Manufacturer: China Support TWI and SPI communication Input voltage (recommended) range from 7V to 12V Input Voltage (limit) range from 6V to 20V 20 digital input/output pins (of which 7 can be used as PWM outputs and 12 as analog inputs) Onboard ATmega32u4 microcontroller with 32KB flash memory, 2.5KB SRAM and 1KB EEPROM
- Add to cart
-
- Arduino, Arduino Shield & Module
Arduino NANO Expansion Shield
- ৳339.00
- Arduino NANO Expansion Shield
- Add to cart
