Dishan Tech BD introduces a specialized selection of Arduino Shields and Modules, catering to both beginners and enthusiasts.
These components enhance Arduino projects by adding features like sensors, displays, motor control, and wireless communication. Engage in hands-on learning through innovative projects, exploring the diverse capabilities of Arduino technology. Dishan Tech BD offers a variety of options to suit individual project needs, making them ideal for your next Arduino venture. Unleash your creativity and dive into the world of electronics with Dishan Tech BD’s Arduino Shields and Modules.
-
- Arduino Shield & Module
1 Channel 5V Relay Board Module
- ৳90.00
- It has a relay status indicator led Power LED(Green), relay status indicator LED(Red) Relay control interface by single-chip IO. Low-level suction close, high-level release. Easy to use, simple 3 line structure.
- Add to cart
-
- Arduino Shield & Module
125KHz RFID Card
- ৳40.00
- Specifications: Contactless transmission of data and supply energy (no battery needed) Operating distance: Up to 1 to 5 cm (Depending on Antenna Geometry) Operating frequency: 125KHz Data transfer: 106 kbit/s Data integrity: 16 Bit CRC, parity, bit coding bit counting Anti-collision Printable
- Add to cart
-
- Arduino Shield & Module
16×2 LCD Keypad Shield
- ৳359.00
- 1602 LCD Keypad Shield for Arduino
- Add to cart
-
- Arduino Shield & Module
2 Channel 5V Relay Board Module
- ৳130.00
- Low Level Trigger Relay Module. RoboticsBD Two separate LEDs for On/Off indication of the Relay. Triggering input voltage 3.3V – 5V Two separate LEDs for On/Off indication of the Relay Triggering input voltage 3.3V – 5V 4) Back EMF protection Back EMF protection 2 LEDs to indicate when relays are ON. Works with logic level signals from 3.3V or 5V…
- Add to cart
-
- Arduino Shield & Module
4 Channel 5V Relay Board Module
- ৳280.00
- No. of Channel: 4 Trigger Voltage: 5VDC Triode drive, increasing relay coil High impedance controller pin Pull-down circuit for the avoidance of malfunction Power supply indicator and Control indicator lamp Power supply and relay instructions, lit, the disconnect is off; The input signal, signal, common Terminal and start conducting;
- Add to cart
-
- Arduino Shield & Module
4×4 Keypad – 16 Key – Matrix Membrane Type
- ৳70.00
- Ultra-thin design & adhesive backing provides easy integration to any project. Excellent price-performance ratio. Easy communication with any microcontroller 5 pins 2.54mm pitch connector, 4x 4type 16 keys. Sticker can peel off for adhesive mounting.
- Add to cart
-
- Arduino Shield & Module, Cables & Connector, Development Board
50 cm Cable For Arduino UNO/MEGA (USB A to B)
- ৳100.00
- USB Type: Type-A to Type-B Weight: 26 gm. Length: 50 cm Long cable for easy work Fully compatible with the PC. Molded strain relief and PVC over-molding to ensure a lifetime of error-free data transmissions.
- Add to cart
-
- Arduino Shield & Module
5V 1 Channel Solid State Relay (SSR)
- ৳350.00
- Power supply:5VDC/160mA Switching Voltage (VAC):240@2A Isolation: Phototriac
- Add to cart
-
- Arduino Shield & Module
5V 2 Channel Solid State Relay (SSR)
- ৳490.00
- Part Number: G3MB-202P Power supply:5VDC/160mA Trigger Voltage (VDC):5 Switching Voltage (VAC):240@2A Isolation: Phototriac
- Add to cart
-
- Arduino Shield & Module
5V 4 Channel Solid State Relay (SSR)
- ৳850.00
- Part Number: G3MB-202P Power supply:5VDC/160mA Trigger Voltage (VDC):5 Switching Voltage (VAC):240@2A Isolation: Phototriac
- Add to cart
-
- Arduino Shield & Module, BMS & Charger, Transformer
5v DC Step Down Transformer Power Supply Module
- ৳180.00
- 5v DC Step Down Transformer Power Supply Module
- Add to cart
-
- Arduino Shield & Module
8 Channel 12V Relay Module
- ৳1,290.00
- Operating Voltage: 12V DC Equipped with high-current relay 10A 250VAC / 10A 30VDC It can control both AC and DC appliances such as Solenoids, Motors, lights, fans, etc. High-quality screw terminals (Terminal Block) provided (C, NC, NO) for quick and easy connection. Freewheeling diode to protect your microcontroller. Input Signal Pin connected to Burg stick for easy accessibility. LED Status…
- Add to cart
-
- Arduino Shield & Module
8 Channel 5V Relay Module
- ৳620.00
- Features: 1. This is a 5V 8 channel relay module with optocoupler isolation. 2. 1 relay output module, max load AC 250A 10A, DC 30V 10A. 3. VCC, GND power input, can separately supply relay power input JD-VCC. 4. Input IN1, IN2, IN3, IN4, IN5, IN6, IN7, IN8 signal line low level trigger. 5. Widely used in SCM control, PLC control, home intelligent control, industry etc.
- Add to cart
-
- Arduino Shield & Module
8 Channel 5V Relay Module
- ৳1,150.00
- Channel: 8 channel Relay Operating Voltage: 5V One normally closed contact and one normally open contact Triode drive, increasing relay coil High impedance controller pin Pull-down circuit for the avoidance of malfunction Power supply indicator and Control indicator lamp Power supply and relay instructions, lit, the disconnect is off
- Add to cart
-
- Arduino Shield & Module
9V Relay
- ৳30.00
- 9V Relay
- Add to cart
-
- Arduino Shield & Module
A6 Pro Serial GPRS GSM Module
- ৳1,050.00
- Working frequency: quad-band network, 850 / 900 / 1800 / 1900MHz Working voltage: 4.8-9VDC(On-board voltage regulator circuit supply power for A6 module) Working Current: maximum of 2A.
- Add to cart
-
- Arduino Shield & Module, BMS & Charger, Sensors
AC 0~5A Analog Current Meter Module Ammeter Sensor Board
- ৳520.00
- Onboard precision microcurrent transformer. Onboard sampling resistor. The module can measure AC currents less than 5A, the corresponding analog output 5A/5mA. Rated input current: 5A Rated output current: 5mA Change: 1000: 1 The linear range: 0 ~ 10A (100 ohms) Linearity: 0.2%
- Add to cart
-
- Arduino Shield & Module, Current, Sensors, Touch
AC Light Dimmer Module, 2 Channel, 3.3V / 5V logic, AC 50 / 60hz, 220V / 110V
- ৳1,055.00
- High-quality BTA16-600B TRIAC AC Voltage: 220V/110V; 50/60Hz Rated current: 5A Logic: 3.3V/5V Peak Operating Current: 8A Dishan Tech BD.
- Add to cart
-
- Sale!
- Arduino Shield & Module, Sensors
AD8232 ECG Measurement Module Kit
- Original price was: ৳2,750.00.৳2,550.00Current price is: ৳2,550.00.
- Designed to extract, amplify, and filter small biopotential signals. Leads-Off Detection. Shutdown Pin. LED Indicator. Analog Output. 3.5 mm Jack for Biomedical Pad Connection. DishanTech BD.
- Add to cart
-
- Arduino Shield & Module
Ai-Thinker RA-02
- ৳695.00
- Specifications 433MHz Average Operating Current TX: 93mA RX: 12.15mA Standby: 1.6mA Best suited for long range Internet of Things application Can be used with Arduino, Raspberry Pi, ARM, PIC etc. - Supports half-duplex SPI communication Color: Multicolor LoRa Spread Spectrum modulation technology Constant RF power output at + 20dBm-100mW voltage change High sensitivity: down to -148dBm Half-duplex SPI communication Programmable…
- Add to cart
-
- Arduino, Arduino Board, Arduino Shield & Module, Development Board
Arduino Micro R3
- ৳1,350.00
- Manufacturer: China Support TWI and SPI communication Input voltage (recommended) range from 7V to 12V Input Voltage (limit) range from 6V to 20V 20 digital input/output pins (of which 7 can be used as PWM outputs and 12 as analog inputs) Onboard ATmega32u4 microcontroller with 32KB flash memory, 2.5KB SRAM and 1KB EEPROM
- Add to cart
-
- Arduino, Arduino Shield & Module
Arduino NANO Expansion Shield
- ৳339.00
- Arduino NANO Expansion Shield
- Add to cart
-
- Arduino, Arduino Shield & Module, Cables & Connector
Arduino Uno Cable
- ৳85.00
- Arduino Uno Cable Type: USB A to B Version: USB 2.0 Length: 50 cm
- Add to cart
-
- Arduino Shield & Module
Ardumoto Shield L298P Motor Driver
- ৳650.00
- L298P based Arduino motor driver shield Forward, Backward steering indicators Can Drive 2 DC Motors Up to 2A of Maximum Current.
- Add to cart
-
- Arduino Shield & Module, Converter Module
Bluetooth Audio Receiver Board
- ৳320.00
- Product name: Bluetooth Decoder Product model: XY-WRBT Working voltage: 3.7~24VDC Bluetooth version: 5.0 Transmission distance: …
- Add to cart
-
- Arduino Shield & Module
Bluetooth Module HC-05
- ৳300.00
- Bases at CSR BC04 Bluetooth technology. with build-in 2.4GHz PCB antenna It’s at the Bluetooth class 2 power level. Range test: 10 meters Operating voltage: 3.3V to 6V DC Operating current in pairing is in the range of 30~40mA.
- Add to cart
-
- Arduino Shield & Module, Robotics Parts
Bluetooth Module HC-06
- ৳310.00
- Bases at CSR BC04 Bluetooth technology. with build-in 2.4GHz PCB antenna It’s at the Bluetooth class 2 power level. Range test: 10 meters Operating voltage: 3.3V to 6V DC Operating current in pairing is in the range of 30~40mA.
- Add to cart
-
- Arduino Shield & Module, Basic Components
Buzzer (3-9V) HQ
- ৳15.00
- Type: Magnetic Transducer, Self Drive (External Drive with Feedback) Sound Pressure Level: 82dB Mounting Type: Through Hole Frequency: 2.3kHz Packaging: Tray Operating Mode: Continuous Voltage Range: 3 ~ 9V DC Voltage - Rated: 5V DC Current Rating: 30mA Size / Dimension: Circular - 12mm Dia x 7.5mm H Termination: Solder Pins/Posts Lead-Free Status: Lead Free RoHS Status: RoHS Compliant
- Add to cart
-
- Arduino Shield & Module
CNC Shield V4
- ৳690.00
- 100% GRBL v0.9 Compatible (PWM Spindle + Soft limits) 3 x Driver slots (drivers not included) Comes assembled and ready to use 3 axis stepper motor driver Compatible with micro-drive laser engraving machine, three-axis CNC engraving machine. 2A can be controlled within the two-phase four-wire stepper motor. Released the digital IO interface, easy to connect to other modules, such as…
- Add to cart
-
- Arduino Shield & Module
Counter Switch module DC 5V 12V 24V Digital Cycle Timer.
- ৳390.00
- Counter Switch module DC 5V 12V 24V Digital Cycle Timer.
- Add to cart
-
- Arduino, Arduino Shield & Module
Data Logger Module Logging Shield Data Recorder Shield for Arduino
- ৳670.00
- Included libraries and example code for both SD and RTC mean you can get going quickly Prototyping area for soldering connectors, circuitry or sensors.
- Add to cart
-
- Sale!
- ACTUATOR'S & ACCESSORIES, Arduino Shield & Module, Sensors, Touch
DC 12V Solenoid Electric Door Lock small
- Original price was: ৳725.00.৳650.00Current price is: ৳650.00.
- Holding force: 0.25 kg Energized forms: intermittent Unlocking time: 1s Dimensions: 27 x 29 x 18 mm (LxWxH) High quality ultra-compact electric lock. Dishan Tech BD.
- Add to cart
-
- Arduino Shield & Module, BMS & Charger, Solar Panel & Charge Controller
DC 5V to 3.5V/12V USB Step Up/Down Power Supply Module
- ৳490.00
- Specification: Input voltage: 3.5V-12V Output voltage: 1.2-24V Output Voltage 1.2V-2V, Used within 2W Output Voltage 2V-20V, Used within 3W Output Voltage 20V-24V, Used within 2.5W Output power = output voltage x output current Product size: 80mm*20mm*10mm/3.14*0.78*0.39'' Paing weight: 15g
- Add to cart
-
- Arduino Shield & Module, Communication Module, Converter Module
DC 8-24V Stereo Digital Amplifier Board DY-AP3015
- ৳395.00
- Parameters: Product name:DY-AP3015 Stereo Power Amplifier Module Model:DY-AP3015 Work Voltage:DC 8V-24V Work Mode:Class D(PWM) Channel:Dual channel Output Power: Output power 18W*2 at 12V 4ohm Output power 10W*2 at 12V 8ohm Output power 15W*2 at 16V 8ohm Output power 20W*2 at 20V 8ohm Output power 30W*2 at 24V 8ohm(Need to add an extra heat sink!) Match speaker(30W~150W): 4ohm at 8V~12V 8ohm…
- Add to cart
-
- Arduino Shield & Module, BMS & Charger, Converter Module
DC DC Step Down Buck Converter Power Supply Module
- ৳286.00
- Features Wide 4.5V to 28V Operating Input Range Up to 92?ficiency Programmable Switching Frequency from 100kHz to 1.5MHz High-Efficiency Pulse Skipping Mode for Ceramic Capacitor Stable Internally Set Current Limit without a Current Sensing Resistor Cycle-by-Cycle Over Current Protection Input Under Voltage Lockout Input Voltage: 4.5V-28VDC Output Voltage: 0.8V-18VDC Continuous Output Current: Max. 3A Perk Output Current: 4A Max. Efficiency:…
- Add to cart
-
- Arduino Shield & Module, BMS & Charger, Converter Module
DC DC Step Down CA-1235 Buck Converter Power Supply Module
- ৳286.00
- Features: This adjustable module uses the United States imported MP1495 chip, synchronous rectifier output. CA-1235 Power supply module converter1.25V 1.5 1.8 2.5 3.3 5V output adjustable 3A 5V-15V input The adjustable module adopts the MP1495 chip imported from the United States, synchronous rectifier output, energy efficiency of more than 90%, non-linear voltage regulator similar to the market. 5-16V 1.25V 1.5V 1.8V…
- Add to cart
-
- ACTUATOR'S & ACCESSORIES, Arduino Shield & Module, DC Gear motor, DC Motors & Wheels, Robotics Parts, Robots
DC Gear Motor
- ৳90.00
- Perfect for robot, projects, and of course you can use it with Arduino! Rated Voltage: 3-6V DC (recommended 5V) Gear Motor rotation speed: 125 RPM Speed without load: 180±10RPM at 6V (no load) Load current: 190 mA (250 mA MAX) continuous, 700mA at no-load start Maximum torque: 800 g. cm min. Stall Current: ~1A Strong anti-interference on this motor keeps…
- Add to cart
-
- ACTUATOR'S & ACCESSORIES, Arduino Board, Arduino Shield & Module, Basic Components, DC Brush Motor, DC Gear motor, Robotics Parts, Robots
DC Gear Motor and Wheel
- ৳175.00
- DC motor specification: Rated Voltage: 3-6V DC. Gear Motor rotation speed: 125 RPM Load current: 190 mA (250 mA MAX). Maximum torque: 800 g. cm min. Wheel specification: Width: 30mm Diameter: 65mm Material: Plastic and rubber Net weight: 65gm (Approx.)
- Add to cart
-
- Arduino Shield & Module, Communication Module, Converter Module
Digital Audio Power Amplifier Board Amp TPA3118 Mono Module
- ৳245.00
- Power amplifier chip: TPA3118 Working Voltage: DC 8-24V Power Output: 1*60W(one Channel, requiring two stereo) Applicable Speaker Impedance: 4-8 ohm Product size: approx. 46*35*11mm/1.81*1.37*0.43'' Net weight: approx. 13g
- Add to cart
-
- Arduino Shield & Module, Communication Module
DT-06 Wireless WiFi Module
- ৳380.00
- DT-06 Wireless WiFi Module
- Add to cart
-
- Arduino Shield & Module
ESP8266 ESP-01 WiFi module (Blue)
- ৳290.00
- Frequency 2.4 GHz Operating Voltage 3.0V ~ 3.6V Supply Voltage ESP8266 ESP-01 Serial WiFi Wireless Transceiver Module Relative Humidity 90 % RH Dimension 16 x 24 x 3.3 mm Working Temperature -40 ~ 125 Deg C Gain + 25 dBm
- Add to cart
-
- Arduino Shield & Module, Sensors
FPM10A Optical Fingerprint Reader Sensor
- ৳3,800.00
- Supply voltage: DC 3.6 ~ 6.0V / 3.3V Supplying Supply Current: Current: <120mA Peak current: <140mA Fingerprint image time: <1.0 seconds
- Add to cart
-
- Arduino Shield & Module
Funduino Joystick Shield V1.A for Arduino
- ৳359.00
- Joystick Shield for Arduino Great experience for game development nRF24L01 Interface Nokia 5110 LCD Interface Bluetooth Interface I2C Interface Compatible with Arduino Operating voltage 3.5V or 5V Color: Red Size: 3.5" x 2.2" x 1.75"
- Add to cart
-
- Arduino Shield & Module, Communication Module
GPRS GSM SIM900
- ৳2,300.00
- Based on SIMCom‘s SIM900 Module Quad-Band 850 / 900/ 1800 / 1900 MHz - would work on GSM networks in all countries across the world. Control by AT commands - Standard Commands: GSM 07.07 & 07.05 | Enhanced Commands: SIMCOM AT Commands. Short Message Service - so that you can send small amounts of data over the network (ASCII or…
- Add to cart
-
- Arduino Shield & Module
GPS GSM GPRS SIM808 Module
- ৳3,300.00
- Quad-band 850/900/1800/1900MHz GPRS multi-slot class12 connectivity: max. 85.6kbps(down-load/up-load) GPRS mobile station class B Controlled by AT Command (3GPP TS 27.007, 27.005 and SIMCOM enhanced AT Commands) Supports charging control for Li-Ion battery Supports Real-Time Clock Integrated GPS/CNSS and supports A-GPS Low power consumption, 10mA in sleep mode.
- Add to cart
-
- Arduino Shield & Module
I2C Display Module
- ৳110.00
- Specification: I2C Address: 0X20~0X27 (the original address is 0X20,you can change it yourself) Supply voltage: 5V the backlight and contrast is adjusted by potentiometer Come with 2 IIC interface, which can be connected by Dupont Line or IIC dedicated cable Compatible for 1602 LCD 2004 LCD
- Add to cart
-
- ACTUATOR'S & ACCESSORIES, Arduino Shield & Module
I2C LCD Adapter Module
- ৳110.00
- 5V power supply. Serial I2C control of LCD display using PCF8574. RoboticsBD Backlight can be enabled or disabled via a jumper on the board. Contrast control via a potentiometer. Can have 8 modules on a single I2C bus (change address via solder jumpers)address, allowing.
- Add to cart
-
- Arduino Shield & Module, Communication Module, IR Sensor, Sensors
Infrared Remote Control Module HX1838
- ৳370.00
- Sensor uses HX1838, high sensitivity.2. Operating voltage 5V.3. Output form: Digital output.4. VCC: 3.3V-5V external voltage (can be directly connected to the 5v microcontroller and 3.3v microcontroller).5. GND: external GND.6. IN: external microcontroller I/O port, I/O port has been designed 10K pull-up resistor.7. Kit theory test distance of about 5-8 meters, but the practical application depends on the ambient factors…
- Add to cart
-
- Arduino Shield & Module, Communication Module
ISD1820 Voice Recording Module
- ৳300.00
- 1. Push?button interface, playback can be edge or level activated 2.Automatic power?down mode 3.On?chip 8? speaker driver 4. Signal 3.3V Power Supply 5.Can be controlled both manually or by MCU 6.Record up to around 10 seconds of audio
- Add to cart
-
- ACTUATOR'S & ACCESSORIES, Arduino Shield & Module
JoyStick 5Pin Breakout Module
- ৳120.00
- Dimensions: 40 x 27 x 15 (LxWxH) mm. RoboticsBD Weight: 10gm (without Hat). 2.54mm pin interface leads. Operating Voltage: 5V. Long service life and stable performance. Standard interface and electronic building blocks. Widely use in Arduino DIY projects.
- Add to cart
-
- Arduino Shield & Module
KY023 KY-023 JOYSTICK Dual Axis XY Joysticks 5 Pin 5V Module
- ৳119.00
- the module has two-way analog output and a digital output interface, the output value corresponding to (X, Y) bi-axial offset, the type of analog; keys that the user press, the Z axis is a push switch read as digital input.
- Add to cart
-
- Arduino Shield & Module, Motor Controller Module
L-298P Motor Driver Expansion Board
- ৳520.00
- Features: L298P dual-end full-bridge drive chip can be used to independently drive two dc, stepper motor or relay at the same time. The current value of the motor can be measured in real time. Fully compatible with Arduino UNO R3, laminated plug-in design, direct reading of current through analog IO. compatible with TinkerKit, can be directly inserted with it.
- Add to cart
-
- Arduino Shield & Module, Motor Controller Module
L293D Motor Driver Module
- ৳320.00
- New L293D motor shield, the input voltage DC4.5-25V 600mA output current capability per channel 1.2A peak output current(non-repetitive) per channel Enable facility Overtemperature protection Logical “0” input voltage up to 1.5V(High noise immunity)
- Add to cart
-
- Arduino Shield & Module, Battery & Holder, BMS & Charger, Robots
Li-Po Battery Voltage Tester
- ৳345.00
- Can be used for 1-8s Lipo/Li-ion/LiMn/Li-Fe Voltage detection precision: 0.01V Cell voltage display range: 0.5V-4.5V Total voltage display range: 0.5V-36V 1S test mode voltage range: 3.7V-30V Low voltage alarm mode for 2-8S Alarm set value range: OFF-2.7V-3.8V When the voltage is below the set value, loud buzzer sounds, pre-set value 3.3V One button setup of alarm voltage Weight: 9g
- Add to cart
-
- Arduino Shield & Module, BMS & Charger, Solar Panel & Charge Controller
Lithium Battery Charging Module TP5100 2A
- ৳210.00
- Features: * Double 8.4v / 4.2v lithium rechargeable single * Programmable charge current 0.1A-2A * Programmable steady precharge current 10% -100%. * Wide operating voltage, maximum reach 18V * Red and green LED charge status indicator * Chip temperature protection, overcurrent protection, undervoltage protection * Battery temperature protection, reverse battery shutdown, short circuit protection * Switching frequency 400Khz, usable inductance…
- Add to cart
-
- Arduino Shield & Module, Basic Components
MAX7219 4 Channel Dot Matrix Display Panel
- ৳640.00
- Driver Chip: MAX7219 Input Voltage: 3.7 to 5.3 V Input Current: 320 mA Display Dimensions: 32x32x6 (LxWxH) mm PCB Dimensions: 128×32 (LxW) mm
- Add to cart
-
- Arduino Shield & Module, Digital ICs
MAX7219 Red Dot Matrix Module MCU Control Display Module
- ৳220.00
- Pin Connection Dot LED Module to the Arduino Vcc – 5V GND – GND DIN – Pin 12 CS – Pin 10 CLK – Pin 11 Features : Requires only 3 communication wires of MCU Cascading multiple Matrix LED Module is very easy Size of the display is very compact The…
- Add to cart
-
- Arduino Shield & Module
MAX9814 Electret Microphone Amplifier Module
- ৳435.00
- Features: Supply Voltage: 2.7v-5.5v @ 3mA current Output: 2Vpp on 1.25V bias Frequency Response: 20Hz 20KHz Programmable Attack and Release Ratio Automatic gain, selectable max from 40dB, 50dB or 60dB Low Input-Referred Noise Density of 30nV/ Low THD: 0.04% (typ) Low Power Shutdown Mode Built-in 2V low-noise microphone bias -40°C ~ +85°C extended temperature range
- Add to cart
-
- Arduino Shield & Module, Motor Controller Module
Motor Driver – Dual TB6612FNG
- ৳410.00
- CW/CCW/short break/stop motor control modes Built-in thermal shutdown circuit and a low voltage detecting circuit Standby control to save power CW/CCW/short brake/stop motor control modes Operating Voltage(VDC): 15 Peak Current (A): 3.2 Continuous Current (A): 1.2 No. of Channels: 1
- Add to cart
-
- Arduino Shield & Module
Motor Shield L293D
- ৳200.00
- 2 connections for 5V ‘hobby’ servos connected to the Arduino’s high-resolution dedicated timer 4 H-Bridges: L293D chipset provides 0.6A per bridge (1.2A peak) with thermal shutdown protection, internal kickback protection diodes. Can run motors on 4.5VDC to 25VDC. Up to 4 bi-directional DC motors with individual 8-bit speed selection (so, about 0.5% resolution) Up to 2 stepper motors (unipolar or…
- Add to cart
-
- Arduino Shield & Module
MT8870 DTMF Audio Decoder Module
- ৳280.00
- Low power device. DTMF decoder chip. Band-split filter. Digital decoding functions. Modem interfaces. Mobile radios.
- Add to cart
-
- Arduino Shield & Module, Communication Module, Converter Module
NRF24L01 Wireless Adapter Module Socket
- ৳215.00
- Specification: Input Voltage: 5V DC Output Voltage: 1.9~3.6 DC Current: 12.3 mA It’s for 8 Pin NRF24L01+ Module A simple socket board which is for NRF24L01 wireless module On-board AMS1117-3.3 chip It can be used with NRF24L01 wireless module Dimension: 26 x 19 x 12mm
- Add to cart
-
- ACTUATOR'S & ACCESSORIES, Arduino Shield & Module
NRF24L01+PA+LNA 2.4GHz SMA Antenna Wireless Transceiver communication module 1pcs
- ৳330.00
- Voltage: 3-3.6V (recommended 3.3V) V. Maximum output power: +20dBm. Power-down mode current: 4.2uA. Operating Range: 1Km Antenna Gain (peak): 2Dbi. 2MB rate (Open area): 520m. 1MB rate (Open area): 750m. 250Kb rate (Open area): 1100m. It uses 2.4GHz global open ISM band, with license free. SPI interface facilitates the communication with MCU I/O port.
- Add to cart
-
- Arduino Shield & Module, Converter Module
Oscilloscope Kit DSO138
- ৳2,690.00
- Specifications: Maximum Real-time Sampling Rate: 1Msps Accuracy: 12Bit Sampling Buffer Depth: 1024 bytes Analog Bandwidth: 0-200KHz Vertical Sensitivity: 10mV / Div - 5V / Div (1-2-5 progressive manner) Input Impedance: 1M? Maximum Input Voltage: 50Vpp (1: 1 probe), 400Vpp (10: 1 probe) Coupling Modes: DC / AC / GND The Horizontal Time Base Range: 10?s / Div - 50s /…
- Add to cart
-
- Arduino Shield & Module
PN532 NFC RFID Read / Write Module V3
- ৳810.00
- Support II2, SPI and HSU (High-Speed UART) I2C / UART: 3.3V ~ 24V TTL SPI: 3.3V TTL with 100-ohm resistors in series Communication distance: 5cm~7cm On-board level shifter, Standard 5V TTL for I2C and UART, 3.3V TTL SPI Work in NFC Mode or RFID reader/writer Mode RFID reader/writer supports: Plug and play, compatible Built-in PCB Antenna, with 4cm~6cm communication distance…
- Add to cart
-
- Arduino Shield & Module, Communication Module, Sensors
Precision Real Time Clock Module DS3231 AT24C32 I2C
- ৳310.00
- Two Time-of-Day Alarms. Digital Temp Sensor Output. Register for Aging Trim. DS 3231 RTC with 2032 Battery Holder. Highly Accurate RTC Completely Manages All Timekeeping Functions. Real-Time Clock Counts Seconds, Minutes, Hours, Date of the Month, Month, Day of the Week, and Year, with Leap-Year Compensation Valid Up to 2100. Configurable I2C device Address for AT24C32 using SMD jumpers on…
- Add to cart
-
- Arduino Shield & Module
RC522 RFID Card Reader Module
- ৳180.00
- Low power consumption, Low cost, and Compact size Read and write chip Fully integrated at 13.56MHz
- Add to cart
-
- Arduino Shield & Module, Motor Controller Module
Regular Motor Driver 43A BTS7960
- ৳650.00
- Input voltage(V): 6 – 27. Maximum current(A): 43. Input level(V): 3.3 – 5. Duty cycle: 0 – 100%. Path resistance: 16 mΩ at 25°C. Low quiescent current: 7 µA at 25°C.
- Add to cart
-
- Arduino Shield & Module, Basic Components
Relay 9V
- ৳30.00
- Model Number: SRD-09VDC-SL-C Coil Power : 9V DC Pin Out: 5 Pin - Coil - COM - NC - NO Nominal Coil Power: 0.36w, 0.45W Contact Capacity: 10A 250VAC/10A 125VAC 10A 30VDC/10A 28VDC Insulation Resistance: 100MΩ.500VDC Operate Time: 15ms/10ms Terminal Type: PCB Contact Load: High Power Product name:: 9V DC Electrical Relay SRD-05VDC-SL-C Contact Ratings: 1A,1C Contact Resistance: 100mΩ(at 10A…
- Add to cart
-
- Arduino Shield & Module, Sensors
SD card Module
- ৳230.00
- All SD SPI pins output, MOSI, SCK, MISO, and CS. Support 5V/3.3V input. This module can handle 2GB SD cards. Size:4.7 x 3.1 cm. LED indicator. SD Card Holder. RoboticsBD Onboard 3.3V regulator (AMS1117-3.3) for +5v to 3.3V generation. 3.3V is also available as output.
- Add to cart
-
- Arduino Shield & Module, DC Brush Motor
Servo Motor Mount Set
- ৳330.00
- Mailing list: 1. Aluminium multifunction steering support X 1 2. Long aluminium U-shaped support X 1 3. imports with glass 4. small round rudder X 2 5. Screw: 3 * 10 1 sets , 4 * 8 4 sets , 3 * 6 2 sets - M2 self-tapping screws 8
- Add to cart
-
- Sale!
- Arduino Shield & Module
SIM800L NEW GPRS GSM Module Core Board Quad-band TTL Serial Port with the antenna
- Original price was: ৳599.00.৳559.00Current price is: ৳559.00.
- TTL serial port for serial port, you can link directly to the micro-controller. Don’t need MAX232. Power module automatically boots, homing network. Onboard signal lights all the way. It flashes slowly when there is a signal, it flashes quickly when there is no signal.
- Add to cart
-
- Sale!
- Arduino Shield & Module, Touch
Solenoid Electric Door Lock DC12V (BIG)
- Original price was: ৳955.00.৳850.00Current price is: ৳850.00.
- Holding force: 0.25 kg Energized forms: intermittent Unlocking time: 1s Dimensions: 54 x 42 x 28 mm (LxWxH) High quality ultra-compact electric lock. Dishan Tech BD.
- Add to cart
-
- Arduino Shield & Module
SSC-32 32Ch Servo Controller Lynxmotion Compatible
- ৳3,300.00
- Controls up to 32 servo motors Comes preassembled USB interface (cable included), Xbee socket, and TTL serial Bidirectional communication with Query commands Large capacitors to prevent brownouts
- Add to cart
-
- Arduino Shield & Module, Communication Module
SX1278 LoRa Module 433M 10KM Ra-02
- ৳845.00
- Communication distance: 15KM Sensitivity: down to -148dBm Programmable bit rates: up to 300kbps RSSI dynamic range: 127dB Wireless frequency: 433MHz Working voltage: 1.8-3.7v Working temperature: -40-+80 ℃ Dishan Tech BD.
- Add to cart
-
- Arduino Shield & Module, Sensors
TTL to RS485 Converter 3.3V / 5V Hardware Automatic Control Converter Module
- ৳935.00
- Anti-Interference Ability Baud rate: 110 ~ 256000bps Operating Voltage: 3v to 30VDC Compatible With Both 3V and 5V logic Dishan Tech BD.
- Add to cart
-
- Arduino Shield & Module, Sensors, Touch
TTP223 Capacitive Touch switch Digital Touch Sensor Module
- ৳109.00
- TTP223 Capacitive Touch switch Digital Touch Sensor Module for Arduino UNO DUE MEGA TTP223 capacitive touch single IC. Onboard level indicator. Working voltage: 2.0V to 5.5V. Dishan Tech BD.
- Add to cart
-
- Arduino Shield & Module, Communication Module
UART EM4100 RFID Card Reader RDM6300
- ৳360.00
- Maximum effective distance up to 150mm Less than 100ms decoding time Support external antenna Uart interface Support EM4100 compatible read-only or read/write tags Small outline design
- Add to cart
-
- Arduino Shield & Module, Sensors
Ultrasonic Transducer Waterproof Distance Measuring Sensor Module
- ৳580.00
- Integrated with wire enclosed waterproof probe, suitable for wet, harsh measurement occasions Small size, easy to use Operating Voltage: 5 V Sonar Sensing Range: 25-450 cm Max. Sensing Range: 450 cm Frequency: 40 KHz.
- Add to cart
-
- Arduino Shield & Module, BMS & Charger
USB Head Switchboard Male Connector to Type-C Micro Female USB 2.54-4P Transfer Test Board
- ৳220.00
- Specifications: Product name: interface converter Product number: XY-USB4 Working voltage: DC 5V Working temperature range: -20 ? ~ 85 ? Operating humidity range: 0% -95% RH
- Add to cart
-
- Arduino Shield & Module, Converter Module
USB Head Switchboard Male Connector to Type-C Transfer Test Board
- ৳120.00
- Specifications: Product name: interface converter Product number: XY-USB4 Working voltage: DC 5V Working temperature range: -20 ? ~ 85 ? Operating humidity range: 0% -95% RH
- Add to cart
-
- Sale!
- Arduino, Arduino Shield & Module
USB to I2C Communication Module for 3D Printer
- Original price was: ৳1,999.00.৳1,950.00Current price is: ৳1,950.00.
- USB to I2C Communication Module for 3D Printer Supply voltage Self-powered: 3.0 to 3.6V USB bus power supply: 4.0 to 5.25V I/O voltage: 1.8V to VDD Temperature range:-40 to 85°C
- Add to cart
-
- Arduino Shield & Module, Communication Module
Voice Recognition Module Kit V3
- ৳2,790.00
- Supply Voltage: 4.5 – 5.5 V. Current : <40 mA. Digital Interface : 5V TTL level for UART interface and GPIO. Support maximum 80 voice commands, with each voice 1500ms (one or two words speaking). Maximum 7 voice commands effective at same time. Arduino library is supplied. User-control General Pin Output
- Add to cart
-
- Arduino Shield & Module, Solar Panel & Charge Controller
XBee USB Adapter
- ৳450.00
- Specifications: - 3.3V and 5V dual power output - 3.3V and 5V IO compatible - USB2.0 protocol - BitBang mode ready - Easily connected to PC via mini USB cable - Support XBee-setting with software X-CTU
- Add to cart
-
- Arduino Shield & Module, BMS & Charger, Solar Panel & Charge Controller
XH-M604 Battery Charger Control Module
- ৳835.00
- Specifications: Input Voltage: DC 6-60V (max 80V) Display Accuracy:0.1V Control Accuracy:0.1V Output Type: direct output Voltage Tolerance:±0.1V Model: XH-M604 Apply For:6-60V MAX 80V battery Use: In the setting voltage value, start button play button raised, about stop button role to down key Item size:81x 54x23mm Item weight:56g
- Add to cart
