-
- Arduino Shield & Module
MT8870 DTMF Audio Decoder Module
- ৳280.00
- Low power device. DTMF decoder chip. Band-split filter. Digital decoding functions. Modem interfaces. Mobile radios.
- Add to cart
-
- Arduino Shield & Module, Communication Module, Converter Module
NRF24L01 Wireless Adapter Module Socket
- ৳215.00
- Specification: Input Voltage: 5V DC Output Voltage: 1.9~3.6 DC Current: 12.3 mA It’s for 8 Pin NRF24L01+ Module A simple socket board which is for NRF24L01 wireless module On-board AMS1117-3.3 chip It can be used with NRF24L01 wireless module Dimension: 26 x 19 x 12mm
- Add to cart
-
- ACTUATOR'S & ACCESSORIES, Arduino Shield & Module
NRF24L01+PA+LNA 2.4GHz SMA Antenna Wireless Transceiver communication module 1pcs
- ৳330.00
- Voltage: 3-3.6V (recommended 3.3V) V. Maximum output power: +20dBm. Power-down mode current: 4.2uA. Operating Range: 1Km Antenna Gain (peak): 2Dbi. 2MB rate (Open area): 520m. 1MB rate (Open area): 750m. 250Kb rate (Open area): 1100m. It uses 2.4GHz global open ISM band, with license free. SPI interface facilitates the communication with MCU I/O port.
- Add to cart
-
- Arduino Shield & Module, Converter Module
Oscilloscope Kit DSO138
- ৳2,690.00
- Specifications: Maximum Real-time Sampling Rate: 1Msps Accuracy: 12Bit Sampling Buffer Depth: 1024 bytes Analog Bandwidth: 0-200KHz Vertical Sensitivity: 10mV / Div - 5V / Div (1-2-5 progressive manner) Input Impedance: 1M? Maximum Input Voltage: 50Vpp (1: 1 probe), 400Vpp (10: 1 probe) Coupling Modes: DC / AC / GND The Horizontal Time Base Range: 10?s / Div - 50s /…
- Add to cart
-
- Arduino Shield & Module
PN532 NFC RFID Read / Write Module V3
- ৳810.00
- Support II2, SPI and HSU (High-Speed UART) I2C / UART: 3.3V ~ 24V TTL SPI: 3.3V TTL with 100-ohm resistors in series Communication distance: 5cm~7cm On-board level shifter, Standard 5V TTL for I2C and UART, 3.3V TTL SPI Work in NFC Mode or RFID reader/writer Mode RFID reader/writer supports: Plug and play, compatible Built-in PCB Antenna, with 4cm~6cm communication distance…
- Add to cart
-
- Arduino Shield & Module, Communication Module, Sensors
Precision Real Time Clock Module DS3231 AT24C32 I2C
- ৳310.00
- Two Time-of-Day Alarms. Digital Temp Sensor Output. Register for Aging Trim. DS 3231 RTC with 2032 Battery Holder. Highly Accurate RTC Completely Manages All Timekeeping Functions. Real-Time Clock Counts Seconds, Minutes, Hours, Date of the Month, Month, Day of the Week, and Year, with Leap-Year Compensation Valid Up to 2100. Configurable I2C device Address for AT24C32 using SMD jumpers on…
- Add to cart
-
- Arduino Shield & Module
RC522 RFID Card Reader Module
- ৳180.00
- Low power consumption, Low cost, and Compact size Read and write chip Fully integrated at 13.56MHz
- Add to cart
-
- Arduino Shield & Module, Motor Controller Module
Regular Motor Driver 43A BTS7960
- ৳650.00
- Input voltage(V): 6 – 27. Maximum current(A): 43. Input level(V): 3.3 – 5. Duty cycle: 0 – 100%. Path resistance: 16 mΩ at 25°C. Low quiescent current: 7 µA at 25°C.
- Add to cart
-
- Arduino Shield & Module, Basic Components
Relay 9V
- ৳30.00
- Model Number: SRD-09VDC-SL-C Coil Power : 9V DC Pin Out: 5 Pin - Coil - COM - NC - NO Nominal Coil Power: 0.36w, 0.45W Contact Capacity: 10A 250VAC/10A 125VAC 10A 30VDC/10A 28VDC Insulation Resistance: 100MΩ.500VDC Operate Time: 15ms/10ms Terminal Type: PCB Contact Load: High Power Product name:: 9V DC Electrical Relay SRD-05VDC-SL-C Contact Ratings: 1A,1C Contact Resistance: 100mΩ(at 10A…
- Add to cart
-
- Arduino Shield & Module, Sensors
SD card Module
- ৳230.00
- All SD SPI pins output, MOSI, SCK, MISO, and CS. Support 5V/3.3V input. This module can handle 2GB SD cards. Size:4.7 x 3.1 cm. LED indicator. SD Card Holder. RoboticsBD Onboard 3.3V regulator (AMS1117-3.3) for +5v to 3.3V generation. 3.3V is also available as output.
- Add to cart
