-
- CNC/3D Printer, Motor Controller Module
A4988 StepStick Stepper Motor Driver Module
- ৳170.00
- This breakout board for Allegro’s A4988 microstepping bipolar stepper motor driver features adjustable current limiting, overcurrent and over-temperature protection, and five different microstep resolutions (down to 1/16-step). It operates from 8 V to 35 V and can deliver up to approximately 1A per phase without a heat sink or forced air flow (it is rated for 2 A per coil with sufficient cooling)DishanTech…
- Add to cart
-
- Motor Controller Module
AC Motor Speed Controller 220V 4000Watt
- ৳645.00
- Description: Operating voltage: AC 220 V. Control voltage: AC 10-220V. Maximum power: 4000W (resistance load), the power should be reduced for a long time. It is recommended to use the resistance load at room temperature within 2000W. Efficiency: 90%. Dimensions: 85 x 55 x 38 mm, buttonhole 6 mm.
- Add to cart
-
- Brush Less Motor, Motor Controller Module
Brushed ESC 20A with Brake
- ৳550.00
- Item type: Brush Motor Speed Controller 20A brush speed controller. Function: forward, reverse, brake Working voltage: 3.0V — 9.4V. Current(A): 20A Driver frequency: 2KHz Input: Li-Po 2S / Ni-Mh/Ni-cd 4-7 cell Constant current 20A Max 25A< 30s> Pulsed 50A< 5s> This ESC can work with 130/180/260/280/380 Brush Motor Item dimension: 10 * 2 * 0.5cm Item weight: 8g
- Add to cart
-
- DC Motors & Wheels, Motor Controller Module
BTS7960 Motor Driver Module
- ৳799.00
- Model: IBT-2 Double BTS7960 large current (43A) H-Bridge motor driver 5v isolate with MCU and effectively protect MCU Can solder heat sink Supply voltage: 5.5-27 V Input level: 3.3-5V Maximum current: 43A Control mode: PWM or level PWM I/P: 25 kHz. Duty cycle: 0-100% Current diagnostic Slope adjustment Dead Time generation Overtemperature, overvoltage, undervoltage, overcurrent protection Short circuit protection
- Add to cart
-
- Motor Controller Module
DRV8825 Purple Stepper Motor Driver
- ৳235.00
- Simple step and direction control interface Six different step resolutions: full-step, half-step, 1/4-step, 1/8-step, 1/16-step, and 1/32-step Can interface directly with 3.3 V and 5 V systems Over-temperature thermal shutdown, over-current shutdown, and under-voltage lockout Short-to-ground and shorted-load protection 4-layer, 2 oz copper PCB for improved heat dissipation Exposed solderable ground pad below the driver IC on the bottom of…
- Add to cart
-
- CNC/3D Printer, Motor Controller Module
DRV8825 Stepper Motor Driver Module
- ৳220.00
- Supply Voltage: 8.2 – 42 VDC. Current Capacity : 2.2A max(24V). Continuous current per phase: 1.5 A. Minimum Logic voltage: 2.5V. Maximum Logic Voltage: 5V. Microstep resolutions: full, 1/2, 1/4, 1/8, 1/16, and 1/32. Dimensions : 15 x 20 mm. Weight: 4 gm.
- Add to cart
-
- Arduino Shield & Module, Motor Controller Module
L-298P Motor Driver Expansion Board
- ৳520.00
- Features: L298P dual-end full-bridge drive chip can be used to independently drive two dc, stepper motor or relay at the same time. The current value of the motor can be measured in real time. Fully compatible with Arduino UNO R3, laminated plug-in design, direct reading of current through analog IO. compatible with TinkerKit, can be directly inserted with it.
- Add to cart
-
- Basic Components, Digital ICs, Motor Controller Module
L293D Dual H-bridge
- ৳119.00
- Maximum Supply Voltage: 36 V Maximum Logic Supply Voltage: 36 V Maximum Input Voltage: 7 V Maximum Enable Voltage: 7 V Peak Output Current (100 ms non-repetitive): 1.2 A Total Power Dissipation at 90°C: 4 W Storage and Junction Temperature: – 40 °C to 150 °C
- Add to cart
-
- Motor Controller Module
L293D Dual Motor Driver Module
- ৳245.00
- Model: L293D Brand: China
- Add to cart
-
- Arduino Shield & Module, Motor Controller Module
L293D Motor Driver Module
- ৳320.00
- New L293D motor shield, the input voltage DC4.5-25V 600mA output current capability per channel 1.2A peak output current(non-repetitive) per channel Enable facility Overtemperature protection Logical “0” input voltage up to 1.5V(High noise immunity)
- Add to cart
-
- DC Motors & Wheels, Motor Controller Module
L293D Motor Driver Shield
- ৳349.00
- DC Motor/Stepper Motor + Servo Shield 2 interface for 5V Servo connected to the Arduino's high-resolution dedicated timer - no jitter. Can drive 4 DC motors or 2 stepper motors or 2 Servo. Up to 4 bi-directional DC motors with individual 8-bit speed selection. Up to 2 stepper motors (unipolar or bipolar) with single coil, double coil or interleaved stepping.…
- Add to cart
-
- Motor Controller Module
L298N DC Motor Driver Module_Green
- ৳335.00
- Driver chip: L298N dual H-bridge DC motor driver chip Driving portion of the terminal supply area Vs: + 5V ~ + 35V; if necessary to take power within the board, the power supply range Vs: + 7V ~ + 35V Part of the peak current drive Io: 2A Logical part of the terminal supply area Vss: + 5V ~ +…
- Add to cart
-
- DC Motors & Wheels, Motor Controller Module
L298N Dual Motor Controller Module (RED)
- ৳195.00
- Operating Voltage: up to 46V Total DC Current: up to 4A On-Board 5V regulator, LM7805 able to provide current up to 500mA-1000mA Maximum Power: 24W Peak Non-Repetitive Output Current (t = 100µS) : 3A Peak Repetitive Output Current (80% ON, 20% OFF, tON=10mS) : 2.5A Peak Continuous Output Current : 2A Typical Logic Supply Voltage : 5V Maximum Supply Voltage : 46V…
- Add to cart
-
- DC Motors & Wheels, Motor Controller Module
L298N Motor Driver (Green)
- ৳349.00
- This module integrates a built-in 5V power supply. When you drive voltage of 7V-35V can onboard 5V logic supply, do not input voltage when using onboard 5V power supply, the +5 V power supply interface, but leads to 5V voltage for external use When ENA is HIGH, IN1 IN2 control OUT1 OUT2 When ENB is HIGH, IN3 IN4 control OUT3…
- Add to cart
-
- Motor Controller Module
Mini PWM 5A 90W PWM 12V DC Motor Speed Controller Module
- ৳140.00
- Mini PWM 5A 90W PWM 12V DC Motor Speed Controller Module
- Add to cart
-
- Arduino Shield & Module, Motor Controller Module
Motor Driver – Dual TB6612FNG
- ৳410.00
- CW/CCW/short break/stop motor control modes Built-in thermal shutdown circuit and a low voltage detecting circuit Standby control to save power CW/CCW/short brake/stop motor control modes Operating Voltage(VDC): 15 Peak Current (A): 3.2 Continuous Current (A): 1.2 No. of Channels: 1
- Add to cart
-
- DC Motors & Wheels, Motor Controller Module
PICkit 3 PIC Microcontroller Programmer
- ৳5,299.00
- • USB (Full speed 12 Mbits/s interface to host PC) • Real-time execution • MPLAB IDE compatible (free copy included) • Built-in over-voltage/short circuit monitor • Firmware upgradeable from PC/web download • Totally enclosed • Supports low voltage to 2.0 volts (2.0v to 6.0v range) • Diagnostic LEDs (power, busy, error) • Read/write program and data memory of microcontroller •…
- Add to cart
-
- Arduino Shield & Module, Motor Controller Module
Regular Motor Driver 43A BTS7960
- ৳650.00
- Input voltage(V): 6 – 27. Maximum current(A): 43. Input level(V): 3.3 – 5. Duty cycle: 0 – 100%. Path resistance: 16 mΩ at 25°C. Low quiescent current: 7 µA at 25°C.
- Add to cart
-
- Sale!
- DC Motors & Wheels, Motor Controller Module, Servo Motor
Servo Tester
- Original price was: ৳320.00.৳295.00Current price is: ৳295.00.
- Operating Voltage: DC 4.2-6.0v Output: Less than 15mA (5.0) Output Signal: 1.5ms ± 0.5ms Simultaneous Servo Test: 3 LED Mode Indicators: Manual / Neutral / Auto Testing Capabilities: Response Time / Neutral Position / Max Angles Size: 46mm x 32mm x 17mm (Approx.) Weight: 8g
- Add to cart
-
- DC Motors & Wheels, Motor Controller Module
TB6612FNG Dual Motor Driver
- ৳559.00
- Power supply voltage: VM = 15V max, VCC = 2.7–5.5V Output current: Iout = 1.2A (average) / 3.2A (peak) Standby control to save power CW/CCW/short-brake/stop motor control modes Built-in thermal shutdown circuit and low-voltage detecting circuit All pins of the TB6612FNG broken out to 0.1" spaced pins Filtering capacitors on both supply lines Dimensions: 0.8x0.8" (LxB)
- Add to cart
-
- DC Motors & Wheels, Motor Controller Module
Water Level Control Switch
- ৳279.00
- Long-lasting life Easy to use Contact Rating: 10 W. Switching Voltage: 220 V. Switching Current: 0.5 A. Breakdown Voltage: 220 VDC. Carry Current: 1 A. Contact Resistance: 100 m?.
- Add to cart
