-
- ACTUATOR'S & ACCESSORIES, Arduino Shield & Module
I2C LCD Adapter Module
- ৳110.00
- 5V power supply. Serial I2C control of LCD display using PCF8574. RoboticsBD Backlight can be enabled or disabled via a jumper on the board. Contrast control via a potentiometer. Can have 8 modules on a single I2C bus (change address via solder jumpers)address, allowing.
- Add to cart
-
- Arduino Shield & Module, Communication Module, IR Sensor, Sensors
Infrared Remote Control Module HX1838
- ৳370.00
- Sensor uses HX1838, high sensitivity.2. Operating voltage 5V.3. Output form: Digital output.4. VCC: 3.3V-5V external voltage (can be directly connected to the 5v microcontroller and 3.3v microcontroller).5. GND: external GND.6. IN: external microcontroller I/O port, I/O port has been designed 10K pull-up resistor.7. Kit theory test distance of about 5-8 meters, but the practical application depends on the ambient factors…
- Add to cart
-
- Arduino Shield & Module, Communication Module
ISD1820 Voice Recording Module
- ৳300.00
- 1. Push?button interface, playback can be edge or level activated 2.Automatic power?down mode 3.On?chip 8? speaker driver 4. Signal 3.3V Power Supply 5.Can be controlled both manually or by MCU 6.Record up to around 10 seconds of audio
- Add to cart
-
- ACTUATOR'S & ACCESSORIES, Arduino Shield & Module
JoyStick 5Pin Breakout Module
- ৳120.00
- Dimensions: 40 x 27 x 15 (LxWxH) mm. RoboticsBD Weight: 10gm (without Hat). 2.54mm pin interface leads. Operating Voltage: 5V. Long service life and stable performance. Standard interface and electronic building blocks. Widely use in Arduino DIY projects.
- Add to cart
-
- Arduino Shield & Module
KY023 KY-023 JOYSTICK Dual Axis XY Joysticks 5 Pin 5V Module
- ৳119.00
- the module has two-way analog output and a digital output interface, the output value corresponding to (X, Y) bi-axial offset, the type of analog; keys that the user press, the Z axis is a push switch read as digital input.
- Add to cart
-
- Arduino Shield & Module, Motor Controller Module
L-298P Motor Driver Expansion Board
- ৳520.00
- Features: L298P dual-end full-bridge drive chip can be used to independently drive two dc, stepper motor or relay at the same time. The current value of the motor can be measured in real time. Fully compatible with Arduino UNO R3, laminated plug-in design, direct reading of current through analog IO. compatible with TinkerKit, can be directly inserted with it.
- Add to cart
-
- Arduino Shield & Module, Motor Controller Module
L293D Motor Driver Module
- ৳320.00
- New L293D motor shield, the input voltage DC4.5-25V 600mA output current capability per channel 1.2A peak output current(non-repetitive) per channel Enable facility Overtemperature protection Logical “0” input voltage up to 1.5V(High noise immunity)
- Add to cart
-
- Arduino Shield & Module, Battery & Holder, BMS & Charger, Robots
Li-Po Battery Voltage Tester
- ৳345.00
- Can be used for 1-8s Lipo/Li-ion/LiMn/Li-Fe Voltage detection precision: 0.01V Cell voltage display range: 0.5V-4.5V Total voltage display range: 0.5V-36V 1S test mode voltage range: 3.7V-30V Low voltage alarm mode for 2-8S Alarm set value range: OFF-2.7V-3.8V When the voltage is below the set value, loud buzzer sounds, pre-set value 3.3V One button setup of alarm voltage Weight: 9g
- Add to cart
-
- Arduino Shield & Module, BMS & Charger, Solar Panel & Charge Controller
Lithium Battery Charging Module TP5100 2A
- ৳210.00
- Features: * Double 8.4v / 4.2v lithium rechargeable single * Programmable charge current 0.1A-2A * Programmable steady precharge current 10% -100%. * Wide operating voltage, maximum reach 18V * Red and green LED charge status indicator * Chip temperature protection, overcurrent protection, undervoltage protection * Battery temperature protection, reverse battery shutdown, short circuit protection * Switching frequency 400Khz, usable inductance…
- Add to cart
-
- Arduino Shield & Module, Basic Components
MAX7219 4 Channel Dot Matrix Display Panel
- ৳640.00
- Driver Chip: MAX7219 Input Voltage: 3.7 to 5.3 V Input Current: 320 mA Display Dimensions: 32x32x6 (LxWxH) mm PCB Dimensions: 128×32 (LxW) mm
- Add to cart
-
- Arduino Shield & Module, Digital ICs
MAX7219 Red Dot Matrix Module MCU Control Display Module
- ৳220.00
- Pin Connection Dot LED Module to the Arduino Vcc – 5V GND – GND DIN – Pin 12 CS – Pin 10 CLK – Pin 11 Features : Requires only 3 communication wires of MCU Cascading multiple Matrix LED Module is very easy Size of the display is very compact The…
- Add to cart
-
- Arduino Shield & Module
MAX9814 Electret Microphone Amplifier Module
- ৳435.00
- Features: Supply Voltage: 2.7v-5.5v @ 3mA current Output: 2Vpp on 1.25V bias Frequency Response: 20Hz 20KHz Programmable Attack and Release Ratio Automatic gain, selectable max from 40dB, 50dB or 60dB Low Input-Referred Noise Density of 30nV/ Low THD: 0.04% (typ) Low Power Shutdown Mode Built-in 2V low-noise microphone bias -40°C ~ +85°C extended temperature range
- Add to cart
-
- Arduino Shield & Module, Motor Controller Module
Motor Driver – Dual TB6612FNG
- ৳410.00
- CW/CCW/short break/stop motor control modes Built-in thermal shutdown circuit and a low voltage detecting circuit Standby control to save power CW/CCW/short brake/stop motor control modes Operating Voltage(VDC): 15 Peak Current (A): 3.2 Continuous Current (A): 1.2 No. of Channels: 1
- Add to cart
-
- Arduino Shield & Module
Motor Shield L293D
- ৳200.00
- 2 connections for 5V ‘hobby’ servos connected to the Arduino’s high-resolution dedicated timer 4 H-Bridges: L293D chipset provides 0.6A per bridge (1.2A peak) with thermal shutdown protection, internal kickback protection diodes. Can run motors on 4.5VDC to 25VDC. Up to 4 bi-directional DC motors with individual 8-bit speed selection (so, about 0.5% resolution) Up to 2 stepper motors (unipolar or…
- Add to cart
-
- Arduino Shield & Module
MT8870 DTMF Audio Decoder Module
- ৳280.00
- Low power device. DTMF decoder chip. Band-split filter. Digital decoding functions. Modem interfaces. Mobile radios.
- Add to cart
-
- Arduino Shield & Module, Communication Module, Converter Module
NRF24L01 Wireless Adapter Module Socket
- ৳215.00
- Specification: Input Voltage: 5V DC Output Voltage: 1.9~3.6 DC Current: 12.3 mA It’s for 8 Pin NRF24L01+ Module A simple socket board which is for NRF24L01 wireless module On-board AMS1117-3.3 chip It can be used with NRF24L01 wireless module Dimension: 26 x 19 x 12mm
- Add to cart
-
- ACTUATOR'S & ACCESSORIES, Arduino Shield & Module
NRF24L01+PA+LNA 2.4GHz SMA Antenna Wireless Transceiver communication module 1pcs
- ৳330.00
- Voltage: 3-3.6V (recommended 3.3V) V. Maximum output power: +20dBm. Power-down mode current: 4.2uA. Operating Range: 1Km Antenna Gain (peak): 2Dbi. 2MB rate (Open area): 520m. 1MB rate (Open area): 750m. 250Kb rate (Open area): 1100m. It uses 2.4GHz global open ISM band, with license free. SPI interface facilitates the communication with MCU I/O port.
- Add to cart
-
- Arduino Shield & Module, Converter Module
Oscilloscope Kit DSO138
- ৳2,690.00
- Specifications: Maximum Real-time Sampling Rate: 1Msps Accuracy: 12Bit Sampling Buffer Depth: 1024 bytes Analog Bandwidth: 0-200KHz Vertical Sensitivity: 10mV / Div - 5V / Div (1-2-5 progressive manner) Input Impedance: 1M? Maximum Input Voltage: 50Vpp (1: 1 probe), 400Vpp (10: 1 probe) Coupling Modes: DC / AC / GND The Horizontal Time Base Range: 10?s / Div - 50s /…
- Add to cart
-
- Arduino Shield & Module
PN532 NFC RFID Read / Write Module V3
- ৳810.00
- Support II2, SPI and HSU (High-Speed UART) I2C / UART: 3.3V ~ 24V TTL SPI: 3.3V TTL with 100-ohm resistors in series Communication distance: 5cm~7cm On-board level shifter, Standard 5V TTL for I2C and UART, 3.3V TTL SPI Work in NFC Mode or RFID reader/writer Mode RFID reader/writer supports: Plug and play, compatible Built-in PCB Antenna, with 4cm~6cm communication distance…
- Add to cart
-
- Arduino Shield & Module, Communication Module, Sensors
Precision Real Time Clock Module DS3231 AT24C32 I2C
- ৳310.00
- Two Time-of-Day Alarms. Digital Temp Sensor Output. Register for Aging Trim. DS 3231 RTC with 2032 Battery Holder. Highly Accurate RTC Completely Manages All Timekeeping Functions. Real-Time Clock Counts Seconds, Minutes, Hours, Date of the Month, Month, Day of the Week, and Year, with Leap-Year Compensation Valid Up to 2100. Configurable I2C device Address for AT24C32 using SMD jumpers on…
- Add to cart
-
- Arduino Shield & Module
RC522 RFID Card Reader Module
- ৳180.00
- Low power consumption, Low cost, and Compact size Read and write chip Fully integrated at 13.56MHz
- Add to cart
